.

Sorry this image is fuzzy :( .. but I wanted to add a caution and this is the best picture I have.

In the tear down manual it says to just lift off the case... but the manual is written for international models that have a CF Card reader rather than a WWAN and SIMMSIM card.

Before lifting off the case you have to reach in with something not-too-sharp and carefully work the sticky tape off the antenna wire.

It's not as easy as it sounds, don't force anything and it will go fine though.

With that worked off you can now lift the case ... I just left the antenna wire on as it's not obvious how to remove it and it does not get in the way much ... but the case will be dangling by thew wire so don't pick it up without supporting it

.




Here's what it looks like with the case off ... that's the harddrive with the "Caution" label on it , lots of parts have sticky tape on them for attaching and insulation, remove it carefully as it will have to be put back on.

Be VERY careful WHERE you put screws down... I had a narrow escape where I almost put the UX down on top of a crewscrew ... remember that's the LCD screen there you do NOT want it rolling around on sharp screw heads.

Pull off the tape as it says in the manual, watch that thin ribbon cable on the harddrive it;sit's fragile.

.


Next takeout the harddrive screws and the metal frame that holds it in, the cushions that hold it are kind of sticky and you have to wiggle and pry it a bit .. as always be careful!

There's one screw in the WLAN (wifi) card it plugs into a standard PCI Express Mini Card slot.

Tale out the SIMMSIM card if you haven't already and the wifi antenna cover and the tiny microphone.

I won't repeat all the stuff from the manual as you really need to read itit, but there are some tiny coaxial plug to come off the WLAN and the ones up to the wifi antennas.

AND more tape to save!

.


Now the Motherboard can be removed.

Again not as easy as it seems in the instructions, the connector is difficult to see as it looks just like a plain ribbon cable or the curcut board.

The trick is first it to tilt up the wifi end of the board, then move it forward a bit THEN lift up the yellow power connector end so it clears the case ... DON'T pry the case as it is fragile especially when not attached to the heavier bottom half

Once it's free tilt it up like in the instructions and disconnect the while plug that's UP under the ribbon cable ..

... see the next picture for a bit better shot of the connector.

.




.

It's not really hidden but it's difficult to identify, in the foreground I'm holding the ribbon cable and the white connector in the blurry background would be above it.

Just gently work it off.

.

Here's an overall shot with the old and new cases at the bottom of the picture. The Motherboard is tillstill attached to the back case by the WWAN coaxial cable.

The Motherboard would not normally need to be disassembled any further for this procedure but I have a picture of some of the inner damage in the next shot and further disassembly to repair it.

.






Circled in Red here is a little hard to see but that screw mount for the WWAN is bent about 20° to the right in this shotshot, luckily the circut board it self was not broken.

I took the WWAN card out and set it aside ... and then bent the steel screw mount back into position with pliers.

Circled in Blue is the broken WWAN module / SIMM card face plate tab .. I glued it back together with crazy glue.

.

.

Here's a Reverse Angle of the Screw mount with the WWAN Modual removed .. thats an alignment pin in front of it that also goes in to a hole in the circuit board.

.




Here's a shot of it all straightened up and more importantly a close up look at the UX's RAM Chips we would not normally get to see ...8 chips = 1 GIG of RAM

This should settle the question of "Is it possible to upgrade the RAM in a UX" questions :)

I can't see risking de-soldering eight, (like what, 1 million leg) RAM chips for a ram upgrade! the heat would probably fry a dozen other components too.

If you've ever seen a 30 foot long 10 ton wave soldering machine working you'd know why they get the connections so neat.

.

Here's a shot of the other side of the motherboard ... check out that HUGE copper plumbing!!

You KNOW it's got to be for the heatsinc ... but I couldn't see (or take enough time to learn) how exactly it hooks up to the processor ... the end we see on the left is rigged up to the fan's heatsinc. Here on the Wiki you can see this part in action in the UX Componetn pictures section.

The fan needed a good blow out too it was pretty dusty ... if youyour UX is overheating it might need the fan cleaned out!

Reassembly is much easier and just the reverse of disassembly ... I rushed through it without taking any more pictures ... just remember to put all the tape back in placeplace, it's there for a reason!

.

Circled in blue are three of the top mounting screw points of the old case in the red circle is where the fourth one broke off and fell in the case

I saved the old case itjust incase, you never knowknow! ... the Duo chip reader is fine and the mouse buttonbuttons etc.

The mouse pointer controller itself is part of the motherboard ...

As I mentioned on the Forum I was all done about midnight or 1 pm and I did NOT even put the battery back in.. I went otto bed and tried it the next morning so I would not stay up all night if it was messed up :) as we get old do we we also grow wise??? :)

In this comparison shot the only thing left is to change the model number (in the green rectangles) ... I might leave it as a faux VGN-UX230P as they are more rare ... what do you think? :)

BTW, the next morning? .... it worked GREAT the first try!!